Search results for query:
Discussions Showcase Albums Media Media Comments Tags Marketplace
1-20 of
500 Results
-
🪛🔧 Technical | Faults | How-to's ❓ℹYeah it's been a while since I serviced the e61 grouphead too, which I probably shouldn't have left this long...
- 12
- 1K
-
🪛🔧 Technical | Faults | How-to's ❓ℹWell, it seems adjusting the pump pressure, 8bar or over it leaks at the top of the e61 mushroom. Scratch that, guess the mushroom just needed tightening as gasket looked fine. Fine at 9 bar. Pump adjuster screw seemed pretty damn tight.
- 12
- 1K
-
🪛🔧 Technical | Faults | How-to's ❓ℹThink it was coming from around there, but didn't have case open. Don't think water is returning to the tank when the pump is running and the opv wasn't stuck, or so I think because was backflushing moments before. Haven't checked actual pressure with a portafilter w pressure gauge at...
- 12
- 1K
-
🪛🔧 Technical | Faults | How-to's ❓ℹHasn't happened again, but instead had a new fun issue, clicking, then brew pump dropping to 2 bar and continuously running until machine turned off at mains.
- 12
- 1K
-
🪛🔧 Technical | Faults | How-to's ❓ℹWould those cause intermittent issues? I'm wondering, saw a while back that someone saw a buildup of particles in the anti backflow valve from a brita filter, could those have caused an issue?
- 12
- 1K
-
🪛🔧 Technical | Faults | How-to's ❓ℹNo knocking, nothing flexing or moving about. Irritating stuff like the vacuum breaker not sealing entirely immediately, but nothing of real note. Possible some gunk was stuck in pump?
- 12
- 1K
-
🪛🔧 Technical | Faults | How-to's ❓ℹWell this is irritating, been like this for a good few days and it seems fine today so far. I'll have a look inside a bit later.
- 12
- 1K
-
🪛🔧 Technical | Faults | How-to's ❓ℹHi, seems like the brew pump under load on my izzo whether brewing or backflushing builds up pressure and then starts to knock/oscillate between 7 and 9 bar a few times a second until it's stopped. Descaled regularly enough (did this after it started), backflush did seem to help albeit the...
- 12
- 1K
-
🪛🔧 Technical | Faults | How-to's ❓ℹOk, turns out pretty easy aside from having to curl pipe and get the nut on the gauge end onto the thread. Curiously, gauge seems to top out at 1 bar, not 1.25 bar like before this stupidness with the gicar unit. Wondering whether I need to adjust the pressurestat now... Cheers
- 3
- 979
-
🪛🔧 Technical | Faults | How-to's ❓ℹTried removing the old manometer for brew pressure at the brass connector just on the left hand side of the boiler, but pipes seem to flex a bit even gripping the pipes with the amount of force to remove it. Any suggestions so I don't end up bending the pipes? Picture here of similar...
- 3
- 979
-
🪛🔧 Technical | Faults | How-to's ❓ℹYeah aside from checking the switch with a meter everything looks fine. If something was fouling the platform would it be occasional?
- 4
- 942
-
🪛🔧 Technical | Faults | How-to's ❓ℹHi, got an izzo alex which normally would cut out when tank is near empty and stop pumping, sounding the alarm buzzer, but twice now it has failed to stop pumping letting the pump run near dry. Possible it's the gicar box or something else?
- 4
- 942
-
-
🪛🔧 Technical | Faults | How-to's ❓ℹLess than a week after a descale.
- 8
- 1.6K
-
🪛🔧 Technical | Faults | How-to's ❓ℹOnly tried this morning, but was only when pulling a shot, not flushing.
- 8
- 1.6K
-
-
🪛🔧 Technical | Faults | How-to's ❓ℹThis morning, brewhead pressure was stuttering between 2 bar difference quite rapidly and didn't sound great on pulling a shot, yet a backflush seemed to keep pressure fine. Guessing if it happens again, something is on its way out like the pump?
- 8
- 1.6K
-
Coffee AccessoriesWhat on earth is the doser sweep made out of, a vane snapped off and it's clearly not metal, some powdery metallic looking epoxy stuff. Presumably can only get parts from somewhere like chriscoffee in the us? Don't think i've seen this on a mazzer...
- 1
- 1K
-
Coffee AccessoriesI was just reading the specs at bellabarista tbh for the fresh, probably the doser they have which makes up so much height. I know the k10 is pretty damn good, had a mini ages back and it simply doesn't compare, figure the eureka is about the same. Even the pours looked different on the k10...
- 7
- 2.3K
-
Coffee AccessoriesI think it's just a bit too damn big to put anywhere these days Retention i've never found too bad in the k10 tbh, but that's if you use it. It's been relatively near the sink but whilst it has been in use every day at least, there's never been issues (because presumably the oils coating the...
- 7
- 2.3K
1-20 of
500 Results